How To Install A Backup Camera In A Car

Guide: How to Install a Backup Camera in a RAM Promaster City

Following up on my previous guide on how to install an aftermarket radio supporting carplay, this guide will show you how to install a backup camera into the stock enclosure.

Parts List

Backup Photographic camera: NATIKA IP69K Waterproof Night Vision 720p Ebay Amazon
Epoxy (I used Loctite repair putty) Ebay Amazon

Tools:

Philips #one and #2 drivers
Wire joining kit: soldering/stripping tools, tap connectors, etc.
Red/blackness wire for 12V power supply
Some long, flexible, but stiff tool for guiding wires within the trunk of the van. I used the outer loop of a hoop skirt.

Wiring

The backup camera requires two things: 12V ability and analog video. The video cable also includes an extra wire which tin can be used to transport the backup signal to the aftermarket radio, merely the Promaster Metropolis already includes that point in the wiring harness, so we won't be needing it.

Nosotros'll get 12V power by tapping into the rear 12V power source, and nosotros'll send analog video on this winding path:

This path follows the mill wiring so the cable will be hidden. Note that I initially tried going on the commuter's side but there's not enough space to pass the cable through in the trunk (where segment E would be), so I had to offset from scratch on the rider's side.

Okay permit'due south begin!

Segment B

It'due south way easier to snake the video cablevision from top to lesser, which is why we're doing segment B showtime. Remove the safety tube from the torso and door frame, then snake the video cable from pinnacle to lesser. It takes some effort, I ended up using the condom hose to push the head downwards, then grab information technology, then pull, and repeat, until I could pull it through.

Segment A

One time that's done, you'll desire to remove the panel on the inside of the driver'southward side left door. Use a panel removal tool or piece of plastic to pry the door off.

In one case done, you'll exist able to see where the photographic camera housing is. Side by side, snake your guide wire (I'one thousand took this from a hoop brim) through these two points.

Tape the cable's connector to the end of the wire, then pull all the fashion through:

Practise the same for the power wire. You'll want to get out about this much hanging from the other end:

Segment B Revisited

Now button your power cable through the prophylactic tubing, going from bottom to pinnacle.

Once complete, yous should take both ability and video coming through the top of the safety tube. Push through the hole in the torso and receive on the other side to complete.

At that place'due south only one cablevision here because I did video starting time, then ability. Just yous can exercise them at the same time.

Segment C

Leave the power cable hanging from the commuter'southward side hole and snake simply the video cablevision to the passenger side pigsty. Same technique, get out the connector taped to the tail of the guide wire and pull through, like you lot would with a needle while sewing.

Segment D

In that location'southward a panel yous'll need to remove to get access for this department merely the pins pull right out when yous pull with your panel removal tool.

Segment E

Remove the panel where you step into the van on the passenger'due south side. It'southward held in place with mainly screws and velcro. You'll demand the Philips #1 caput for these screws.

Pass the cable through, following the existing wire, merely don't get past the door yet.

Segment F

Yous'll desire to remove the aforementioned step panel in the rider cabin.

Before you can remove it, you'll demand to undo a unmarried screw where the passenger's feet go. Then, pop the panel off.

Now that both sections are accessible, snake the wire all the fashion through.

Segment G

The rug underneath the glove box is held in identify with two pins, pull to release, then run the cable forth the bottom.

Segment H

Snake the cablevision through to the inside of the dash.

At this point you can tie the cable to the car's wiring harness with either tesa record or a zip tie.

Tapping Power

Remove the 12V vehicle power from the commuter's side rear by pushing in and pushing up:

The power supply cable that comes with this camera isn't long enough. Cut around 5 ft of your ain wire, bind together with tesa tape or zip ties, and snake through to the superlative hole so you can meet the existing power supply cable.

Strip both wires and join them. I used solder.

Then zip tie the bundle and stash away in that hole.

On the other end, yous'll demand to tap into the power supply. I stripped the wire and soldered my new wire inline:

I messed up my first attempt, be certain to leave aplenty exposed wire for soldering!

Testing

It's e'er practiced to examination early so if anything went wrong you can fix information technology without having to disassemble things once more.

Connect the camera to power and video, connect video to your radio, try putting your car in reverse and seeing if information technology works. If it doesn't work, test the leads for power and video. Note that in the pioneer radio you have to get into the settings to enable the fill-in camera or AV input.

Mounting the Photographic camera

I spent a lot of time considering my options for bracketing the camera on. Afterwards all, it y'all tin encounter in the picture that in that location are two holes for screws. Even so, I constitute it then incredibly unwieldy to work in the small space that I abandoned this plan (later on losing a few screws to the void below). Instead I used epoxy, which hardens to produce a waterproof seal and binds the materials together.

It looks roomy in this picture only in that location's barely enough space to fit my fingers, let alone a screwdriver.

You lot'll want to cutting out a large enough square pigsty to sit the unabridged front part of the camera in. Cutting a circular hole and sitting the camera behind it won't work with this camera I've chosen, as it'due south such a broad bending that the plastic obstructs function of its view.

Offset with the smallest hole and line it up with the center.

I followed up with the largest drill scrap I had, and then used my dremel to cutting away at material until the photographic camera fit snugly.

Adjacent cut out a slice of epoxy, follow directions to mix thoroughly. If you lot oasis't used epoxy earlier (like me), try it out on some other materials before you do the terminal adhesion, to go the hang of it.

Steps you'll want to proceed in mind are:

Make certain yous tin can set the epoxy 24 hours, equally close to room temperature as possible (below 60 degrees and it starts beingness problematic).
Encompass the photographic camera lens with painter'due south record so you don't become it dirty.
Clean all surfaces thoroughly.
Use a file or sandpaper to add together some texture to the camera body.

I don't know how information technology'll concord up, simply information technology seems to work right now. In the time to come I'll detect a way to paint the epoxy so it matches the color of the license frame besides.

Finalizing the Wiring

After testing everything works one terminal time, use zip ties or tesa tape to tie the cables where appropriate. For instance y'all probably want to tie the video cable to the factory cablevision lines to keep things cracking. When yous're done, you can re-install your radio and re-attach the panels from earlier.

And that'southward it. Let me know in the comments below if yous take any questions (if anything is unclear, etc). Thanks for reading.

Source: https://medium.com/@chris_41792/guide-how-to-install-a-backup-camera-in-a-ram-promaster-city-db479dd2fe78

Posted by: crossleyhustend.blogspot.com